search for




 

A Brief Review of κ-Carbide in Fe-Mn-Al-C Model Alloys
Applied Microscopy 2018;48:117-21
Published online December 28, 2018
© 2018 Korean Society of Microscopy.

Jae Bok Seol

National Institute for Nanomaterials Technology (NINT), POSTECH, Pohang 37673, Korea
Correspondence to: *Correspondence to: Seol JB, http://orcid.org/0000-0001-9143-4274, Tel: +82-54-279-0220, Fax: +82-54-279-0249, E-mail: jb_seol@postech.ac.kr
Received December 21, 2018; Revised December 26, 2018; Accepted December 27, 2018.
This is an open-access article distributed under the terms of the Creative Commons Attribution Non-Commercial License (http://creativecommons.org/licenses/by-nc/4.0) which permits unrestricted noncommercial use, distribution, and reproduction in any medium, provided the original work is properly cited.
Abstract

The multiple length scale analysis of previously designed Fe-Mn-Al-C based low-density model alloys reveals the difference in ordered κ-carbide, (Fe,Mn)3AlCx, between Fe-25Mn-16Al-5.2C (at%) alloy and Fe-3Mn-10Al-1.2C (at%) alloy. For the former alloy composition consisting of fully austenite grains, κ-carbide showed majorly cuboidal and minorly pancake morphology and its chemical composition was not changed through aging for 24 h and 168 h at 600°C. Meanwhile, for the isothermally annealed ferritic alloy system for 1 hr at 500 and 600°C, the dramatic change in the chemical composition of needle-shape κ-carbide, (Fe,Mn)3(Fe,Al)Cx, was found. Here we address that the compositional fluctuations in the vicinity of the carbides are significantly controlled by abutting phase, either austenite or ferrite. Namely, the cooperative ordering of carbon and Al is an important factor contributing to carbide formation in the high-Mn and high-Al alloyed austenitic steel, while the carbon and Mn for the low-Mn and high Al alloyed ferritic steel.

Keywords : Low-density steels, High manganese and aluminum alloyed steels, Ordered carbides, Transmission electron microscopy, Atom probe tomography
References
  1. Bang, CW, Seol, JB, Yang, YS, and Park, CG (2015). Atomically resolved cementite dissolution governed by the strain state in pearlite steel wires. Scripta Mater. 108, 151-155.
    CrossRef
  2. Chao, CY, Hwang, CN, and Liu, TF (1993). GRAIN-BOUNDARYPRECIPITATION IN AN FE-7.8 AL-31.7 MN-0.54 C ALLOY. Scripta Metall Mater. 28, 109-114.
    CrossRef
  3. Choi, K, Seo, CH, Lee, H, Kim, SK, Kwak, JH, Chin, KG, Park, KT, and Kim, NJ (2010). Effect of aging on the microstructure and deformation behavior of austenite base lightweight Fe–28Mn–9Al–0.8C steel. Scripta Mater. 63, 1028-1031.
    CrossRef
  4. Connétable, D, and Maugis, P (2008). First principle calculations of the κ-Fe3AlC perovskite and iron–aluminium intermetallics. Intermetallics. 16, 345-352.
    CrossRef
  5. Gutierrez-Urrutia, I, and Raabe, D (2012). Multistage strain hardening through dislocation substructure and twinning in a high strength and ductile weight-reduced Fe–Mn–Al–C steel. Acta Mater. 60, 5791-5802.
    CrossRef
  6. Gutierrez-Urrutia, I, and Raabe, D (2013). Influence of Al content and precipitation state on the mechanical behavior of austenitic high-Mn low-density steels. Scripta Mater. 68, 343-347.
    CrossRef
  7. Noh, JY, and Kim, H (2011). Density Functional Theory Calculations on κ-carbides, (Fe, Mn)3AlC. J Kor Phys Soc. 58, 285-290.
    CrossRef
  8. Raabe, D, Springer, H, Gutierrez-Urrutia, I, Rosters, F, Bausch, M, Seol, JB, Koyama, M, Choi, PP, and Tsuzaki, K (2014). Alloy Design, Combinatorial Synthesis, and Microstructure–Property Relations for Low-Density Fe-Mn-Al-C Austenitic Steels. JOM. 66, 1845-1856.
    CrossRef
  9. Seol, JB, Jung, JE, Jang, YW, and Park, CG (2013). Influence of carbon content on the microstructure, martensitic transformation and mechanical properties in austenite/ɛ-martensite dual-phase Fe–Mn–C steels. Acta Mater. 61, 558-578.
    CrossRef
  10. Seol, JB, Raabe, D, Choi, P, Lim, YR, and Park, CG (2012). Atomic scale effects of alloying, partitioning, solute drag and austempering on the mechanical properties of high-carbon bainitic–austenitic TRIP steels. Acta Mater. 60, 6183-6199.
    CrossRef
  11. Seol, JB, Raabe, D, Choi, P, and Park, HS (2013). Direct evidence for the formation of ordered carbides in a ferrite-based low-density Fe–Mn–Al–C alloy studied by transmission electron microscopy and atom probe tomography. Scripta Mater. 68, 348-353.
    CrossRef
  12. Springer, H, and Raabe, D (2012). Rapid alloy prototyping: Compositional and thermo-mechanical high throughput bulk combinatorial design of structural materials based on the example of 30Mn–1.2C–xAl triplex steels. Acta Mater. 60, 4950-4959.
    CrossRef
  13. Yao, MJ, Dey, P, Seol, JB, Choi, P, Herbig, M, Marceau, RKW, Hickel, T, Neugebauer, J, and Raabe, D (2016). Combined atom probe tomography and density functional theory investigation of the Al off-stoichiometry of κ-carbides in an austenitic Fe–Mn–Al–C low density steel. Acta Mater. 106, 229-238.
    CrossRef


December 2018, 48 (4)
  • Science Central
  • CrossMark
  • Crossref TDM