search for




 

Microstructural Evolution and Recrystallization Behavior Traced by Electron Channeling Contrast Imaging
Applied Microscopy 2018;48:130-1
Published online December 28, 2018
© 2018 Korean Society of Microscopy.

Jin-Su Oh, and Cheol-Woong Yang*

School of Advanced Materials Science & Engineering, Sungkyunkwan University, Suwon 16419, Korea
Correspondence to: Yang CW, http://orcid.org/0000-0003-0475-8399, Tel: +82-31-290-7362, Fax: +82-31-290-7371, E-mail: cwyang@skku.edu
Received December 25, 2018; Revised December 27, 2018; Accepted December 27, 2018.
This is an open-access article distributed under the terms of the Creative Commons Attribution Non-Commercial License (http://creativecommons.org/licenses/by-nc/4.0) which permits unrestricted noncommercial use, distribution, and reproduction in any medium, provided the original work is properly cited.
Abstract

Electron channeling contrast imaging (ECCI) is one of the imaging techniques in scanning electron microscopy based on a variation in electron backscattering yield depending on the direction of the primary electron beam with respect to the crystal lattice. The ECCI provides not only observation of the distribution of individual grains and grain boundaries but also identification of the defects such as dislocations, twins, and stacking faults. The ECCI at the interface between recrystallized and deformed region of shot peening treated nickel clearly demonstrates the microstructural evolution during the recrystallization including original grain boundaries, and thus can provide better insight into the recrystallization behavior.

Keywords : Electron channeling contrast imaging, Recrystallization, Shot peening, Original grain boundaries
Body

Shot peening is a process that improves the mechanical properties of a metal or alloy target by plastic-deforming the target surface. Shot peening on the surface results in a linear decrease in the level of plastic deformation in the depth direction from the surface of the nickel. Accordingly, when the heat treatment is conducted, recrystallization process proceeds as a function of annealing time in the depth direction from the surface where the plastic deformation is severe. In this experiment, heat treatment was performed at 700°C for 5 minutes. The cross-sectional specimen was prepared by mechanical polishing before heat treatment and observed at the condition of the acceleration voltage of 30 kV, the probe current of 20 nA, and the working distance of 7.3 mm in COMPO mode using JEOL JSM-7000F field emission SEM. All areas at about 200 μm deep from the surface were recrystallized. The above electron channeling contrast image was obtained at the border (orange dashed line) where the recrystallization ended in the 5 minute heat treatment. The electron channeling contrast imaging (ECCI) is a technique that shows the contrast induced by the difference in the backscattering yield of electrons according to crystal orientation (Lloyd, 1987). This technique is useful for observing the effect of plastic deformation because the yield of backscattering varies sensitively even with small angle difference. Therefore, recrystallized region and remaining area deformed by shot peening can be easily distinguished, as indicated by orange dashed line. The defects such as twins and stacking faults in the recrystallized grains were clearly observed as well. Furthermore, the original grain boundaries (green dashed line) of shot-peened nickel were thermally etched by the heat treatment for recrystallization (García de Andrés et al., 2002), standing out as a remarkable surface morphology. This morphology even remains after the recrystallization has occurred, so that the original grain boundaries can be easily observed as shown in the image. Consequently, the ECCI including original grain boundaries can clearly demonstrate the microstructural evolution during the recrystallization, and thus can provide better insight into the recrystallization behavior.

ACKNOWLEDGMENTS

This work was supported by the National Research Foundation of Korea(NRF) grant funded by the Korea government (MSIP) (2018R1A5A6075959).

CONFLICT OF INTEREST

No potential conflict of interest relevant to this article was reported.

References
  1. Lloyd, GE (1987). Atomic number and crystallographic contrast images with the SEM: a review of backscattered electron techniques. Mineral Mag. 51, 3-19.
    CrossRef
  2. García de Andrés, C, Caballero, FG, Capdevila, C, and San Martín, D (2002). Revealing austenite grain boundaries by thermal etching: advantages and disadvantages. Mater Charact. 49, 121-127.
    CrossRef


December 2018, 48 (4)
Full Text(PDF) Free

Social Network Service
Services

Cited By Articles
  • CrossRef (0)

Author ORCID Information

Funding Information
  • Science Central
  • CrossMark
  • Crossref TDM